Announcement

Collapse
No announcement yet.

User Profile

Collapse

Profile Sidebar

Collapse
NoDNA
NoDNA
Senior Member
""Retired and been cutting, carving for several years. I travel and vol at state and federal parks so carving gives me a little time out"
Last Activity: Yesterday, 02:39 PM
Joined: 03-07-2018
Location: Currently Oregon NW.
  •  
  • Filter
  • Time
  • Show
  • Source
Clear All
new posts

  • NoDNA
    replied to The Big Aht
    Marangoster,, I would be so lucky to have some "yard art " like that.. That is really a nice ant, and welcome to the group
    See more | Go to post

    Leave a comment:


  • https://www.woodworkingshop.com/search.aspx?q=files


    This is where I got my small files Good small ones and they are great and work real good in my small animals.
    See more | Go to post

    Leave a comment:


  • NoDNA
    replied to CA Glue
    After all these ideas and great ideas, I thanks you all for the input. Now I did just last night while working on my Alabaster bear. THE EAR broke off in small pieces, stone in not like wood, so I got to thinking about mixing sanding dust of the stone into the broken area. With CA,, actually folks it...
    See more | Go to post

    Leave a comment:


  • Thanks BobD, My new one has two speeds, one speed is 1580 fpm and the other is 2650, my old one I had been using was turning at a break neck speed of 850, Doing a meanial ok but A) no power and would stop at the least about of pressure, B) no height 4.5" . And I haven't done any metal cutting...
    See more | Go to post

    Leave a comment:


  • NoDNA
    started a topic Band saw Questions

    Band saw Questions

    I just purchased a new "larger" band saw, can now cut 6" deep.. For me that is a bonus, .. Question 1 is with 2 speeds, I think that if I run a faster speed it may "burn" the blade or wood" The blades I have are 3/8" x 6 TPI, 3/8 x 15 TPI and 1/8" x 6 TPI ....
    See more | Go to post

  • NoDNA
    replied to Busy week a head
    Well , all that been said, I have had the croup/skuzz/ barking like a fox along with a real box in my throat. Akin to swallowing a dried out pine cone backwards.. Now even feeling like doing any chip flipping. ...
    See more | Go to post

    Leave a comment:


  • NoDNA
    replied to Carving Mallets
    OH, Arthur, sometimes if the carving does' not respond, I just make it into something smaller. OR wind up on the other side of the shop,,, tossed....
    See more | Go to post

    Leave a comment:


  • NoDNA
    replied to Carving Mallets
    And that is something too. I has a past home/barn builder and re-modeler.. only hit nails and move heavy timber with a "mallet". This carving thing is somewhat new to me, and my projects are too small to be hitting,,.....
    See more | Go to post

    Leave a comment:


  • NoDNA
    replied to Carving Mallets
    SlimGeezer, one time a long ago, a fellow told me that he could control the hits better with a "round mallet" . If I hear you correctly the one I am talking about is ,, it is tapered towards the handle larger on the long end. His was about 5 inches round"ish" top and 2" at the...
    See more | Go to post
    Last edited by NoDNA; 11-21-2019, 06:31 PM.

    Leave a comment:


  • NoDNA
    replied to Question on Black and Decker rotary tool
    I have had the 4x36 for just over a year, the motor to main drive belt went, I had to get from a auto parts store and the cheep metal guide adjuster keeps bending and allowing the belt to cut into the sides. Then the dust pickup under neath has worn so badly, I have used a tube of metal putty to repair...
    See more | Go to post

    Leave a comment:


  • NoDNA
    replied to CA Glue
    Bottles,,Thanks fellas, I have a"bottle" of Titebond CA.. had to put in a vice and "press the ^%$^%$" out of it to get the lid off. wrote a note to that company, never heard a word back, they must have the same problem..
    Anyway will keep trying .. and tbox61 , ha I just want...
    See more | Go to post

    Leave a comment:


  • NoDNA
    started a topic CA Glue

    CA Glue

    I know most everyone uses this stuff and it is a pain in the &^(&^%(. to use out of the tubes it comes in. Just about every brand I get the top will adhere to it's self and I cannot get the top off most all the time. One thing I did do though is put Vaseline, on the threads , that seemed...
    See more | Go to post

  • NoDNA
    replied to "That The Army Goes Rolling Along!"
    SHUT THE DOOR EDDY!!! That is terrific.. So good.
    Thanks for that one, bettcha Sarg will love it..
    Chuck...
    See more | Go to post

    Leave a comment:


  • NoDNA
    replied to Not my carving…
    That is pretty neat,, put it on the front door,, maybe the sales guys won't come by? I think your buddy did a good job though, and I do like "those eyes" .
    Chuck...
    See more | Go to post

    Leave a comment:


  • NoDNA
    replied to Owls, Indians, and Gnome samples
    Say, I was just asked to make up a Chess set,, now this is a great job and I think you are The Man.. Thanks for the share..
    Chuck...
    See more | Go to post

    Leave a comment:


  • NoDNA
    replied to vets day
    And all, when I meet some fellow Vets, with their wives, I always thank those ladies too. As if it weren't for their support, the vets would have had a harder time. Also all the vets that are still in hospitals, care homes they are too the forgotten ones.
    I am going to cut out some small reindeer...
    See more | Go to post

    Leave a comment:


  • NoDNA
    replied to 2019 Ornament Swap * official thread
    Now ,, I am cornfuzed..lionslair. I was going to send all mine to the Grandkids.. ..Ok November 1st is gone and ?? Keoma
    See more | Go to post

    Leave a comment:

No activity results to display
Show More
Working...
X